Widescreen Gaming Forum

I don't know if this has been answered before but i know it support 3x 27" monitors but what about the 4th top spot? can i put another 27 or what size will it fit there?

Yes, it supports 27" panels in all four positions.

Hi Skip, have you tried the 27 inch curved panel from samsung(or others) on the 3+1 config? I am planning to buy two Samsung 27 inch(planning to buy the third one during black Friday the yr) and your 3+1 config, Want to know if the 3+1 config support two 27 inch curved mounted on the outer mounts. Can the outer ones be adjusted to line up by the edge to cover the empty middle one?

Any chance the stand goes on sale again?

Thanks Deathblade...

anujcb, I have not tried with curved 27" panels. I have tried with the curved 34" ultra-wide by LG. I've used in a triple Landscape with 2x 25" U2515 from Dell, and it worked fine (though REALLY big). I currently have it in PLP with those same to 25" on the L/R in Portrait.

I don't see what you couldn't adjust everything like you wanted. What's the model of Samsung?

Model of the Samsung curved monitorI am planning to purchase is - S27E510CS

I have another question, My final goal is to set up a 3+ 1 configuration, since I don't have the money right now to spend for this config right away I am planning to do the following in the order. Can you validate if this is a viable plan?


Buy Ergo tech - 100-D28-B13 for $214 - Is it available in WSGF or is it only available in ergotech website?
Buy two S27E510CS from costco - $598+tax

.....Hook up the two Samsung(S27E510CS) and an old Asus I have(VW266H) in 2+1 config

......In a few months time

Buy Upgrade Kit: 3x1-XL(WSGF-5S) - $125
Buy a third S27E510CS(or something similar) $299+tax(or less)

...This will complete the 4+1 configuration.

anujcb,

I moved your posts into this thread, as they are better suited here.

Yes, the plan you have regarding the stand will work. The cheapest I've seen the 100-D28-B13 is at Amazon.com. It's also the reason I don't sell it anymore. They sell it for less than what I can purchase it for.

http://amzn.to/1Gi1W9Q

I'm new here and I am considering buying this monitor stand. I have a couple questions for a particular setup I want to use.

I plan on using the 3+1 monitor configuration with 3 x Asus PB278Q 27" monitors in landscape on the bottom row, and have a 32" TV on top (http://www.frys.com/product/8400928?sit ... IN_RSLT_PG).

Is this set up to ambitious and should I get a smaller TV? I am also worried about the weight. The Asus Monitors weigh in roughly 20 lb and the TV is roughly 13 lb.

Thanks.

I think you'll be okay on the weight. From what I've read on the Asus PB278Q, that weight is with the base still attached. Removing the base removes a significant amount of weight from the display. Do you have any of those panels now? Can you weigh one without the base attached?

You may run into an issue with the overall height. I've just gotten in some taller poles that I will be placing in the store shortly. They are 36", compared to the 28" pole that is standard in the kit. I checked the TV, and you'll need one of the VESA adapters that we sell in the store, as the TV uses a VESA pattern of 200x200.

Currently have 3 Benq 2720xl's and was wondering if I could mount a 34" curved or flat monitor as my plus one above or below? Thanks in advance.

Yes, this will work. I would probably go flat, given the weight and weight distribution of the curved panels (and my experience with the VESA mount on the curved LG).