Widescreen Gaming Forum

Have three Sharp PN-K321s (4K at 60Hz) and no stand can accommodate all three of them!

Please help me locate one!

I have plans for a custom "mega" version of the WSGF stand. You could be my first customer. We're probably looking t $700 - almost 2x the cost of the WSGF stand. Let me know if you're interested...

Thought I posted a reply but it didn't go through.

Yes, I would like one.

Lead-time? Shall I send you the money now?

Issue was that you were still on "mod review" due to your new status on the forum. Welcome! That is now fixed.

Gimme a week or so. I've just recently sent out a survey about our stand sales to date and customer experiences. I'm working on a couple of solutions, based on feedback from those users.

My plan is to take two WSGF stands, and combine them into one unit. It will be a 7-Segment Bar, that uses two bases for support.

http://www.wsgf.org/products/freedom-ws ... desk-stand

Currently, the stands are as such: 1 - 2 - 3 - 4 - 5. With the bar attaching to the pole in the three segment.

My plan is to merge two of the bars together into one unit as such: 1 - 2 - 3 - 4 - 5 - 6 - 7. With the bar attacking on two poles - segments two and six.

There isn't enough room to put two stands side-by-side, with them attached at points 3 and 5. I think the stands would bump into each other, and we wouldn't solve all the flex issues on the outer ends. You have to use an odd number of segments, so that you can put a panel in the middle.

I think nine segments would just be too wide. Maybe not. But at this point you could probably do 40"+ TVs. Just my guess. 5x1-Landscape is available now with Eyefinity. Maybe people want support for that. Maybe I will leave those segments on and let people remove them if they want.

I've just got to get a bit of time with my local machine shop to sort things out...

But, this is the first peak into the planning stages. Let me know your feedback. It will help me set up the first beta kit. I will load that into the store, so that it can be sold on an actual transaction.

I'd be more comfortable sending you the money first as encouragement.

I want the item to be Anodized Matte Black.

It must support all three of my PN-K321 (31.5 Inches each) at 9lbs each.

I've gotta a prototype built. You can see a video below.



Let me know what you think. I've set up a forum thread to collect questions.

http://www.wsgf.org/forums/viewtopic.php?f=93&t=27608

I will check.

What about 3x30"rs? Also, would there be a way to mount a 4th 30" above? My current setup is like this, but I have a lot of stands on my desk.

_________________
System Core: | Intel Core i5-2500K + ASUS P8Z68-V + 16GB Corsair XMS3 DDR3 1333 MHz | Win7 x64 | MSI R7970 Lightning 3GB [1105/1400] |
Display: | 3 x Dell Ultrasharp 3007WFP-HC @ 7680x1600 | Dell u3011 |

30" should work fine as well. Once I switch stock over to the WSGF Ultimate v2, I plan to combine two of these for future orders (they will be more expensive). There will be two tall poles, and you could try a monitor above. Not sure about the total height though. What is your monitor height?

(Bottom) 3007wfp = Width 27" Height 5.75"
(Top) u3011 = Width 27.5" Height 5.75"

_________________
System Core: | Intel Core i5-2500K + ASUS P8Z68-V + 16GB Corsair XMS3 DDR3 1333 MHz | Win7 x64 | MSI R7970 Lightning 3GB [1105/1400] |
Display: | 3 x Dell Ultrasharp 3007WFP-HC @ 7680x1600 | Dell u3011 |