| Widescreen Gaming Forum http://www.wsgf.org/phpBB3/ |
|
| Correct FOV/and unstrectched values in ArtMoney http://www.wsgf.org/phpBB3/viewtopic.php?f=64&t=12867 |
Page 1 of 1 |
| Author: | wickedwings [ 30 Dec 2005, 21:01 ] |
| Post subject: | Correct FOV/and unstrectched values in ArtMoney |
Any ideas of the possible values we can try using ArtMoney to change the correct FOV /or aspect ratio / so the image won't be strectched. Some games seem to be able to auto adjust correctly based on the vertical/horizontal res. Some are fixed at 4:3. What possible values I should look for to change? 04 and 03? integers? how many bytes (1 2 3 4?). Any help is appreciated. Much thanks. |
|
| Author: | fuc847 [ 30 Dec 2005, 22:10 ] |
| Post subject: | Correct FOV/and unstrectched values in ArtMoney |
u can try looking for 1.33333333 since 4/3 is 1.333333 |
|
| Author: | wickedwings [ 30 Dec 2005, 22:51 ] |
| Post subject: | Correct FOV/and unstrectched values in ArtMoney |
1.3333 is difficult to find since I don't know how many .3333s or the right variable (real number) sign/or unsign the number of bytes, etc. I was hoping someone with games programming knowledge can help. What are the typical methods can be used to assign variables for 4:3 aspect ratio and FOV's=90, 100, etc.. Thanks. |
|
| Author: | Rope [ 09 May 2012, 17:40 ] |
| Post subject: | I know this topic is super |
I know this topic is super old, but I didn't want to create a new one since the topic opener asks exactly what I wanted to ask. Recently I was able to fix the resolution and FOV of Silent Hill 4 using a table made in ArtMoney (by user Garnet) that had the FOV data already filtered out, ready to be edited with the desired values. Now I'm trying to find the same FOV data for another game, ObsCure II, but I have no idea how. The guide for ArtMoney that is around the web only teaches you how to find the data for the resolution, not the FOV. So.... anyone can help? |
|
| Author: | helifax [ 09 May 2012, 19:02 ] |
| Post subject: | Well,1st you need to know |
Well, 1st you need to know how the data is stored in the memory. 1.3333333 is hard to find and that is a "float". Floating numbers are not stored in memory as floats. Data in memory is usually stored in 4bytes (or more, a long theory here) and in hex. So what you to look for is the equivalent of the 1.3333 in hex:) Hope this helps:) Best Regards, Helifax |
|
| Author: | HaYDeN [ 09 May 2012, 23:44 ] |
| Post subject: | Artmoney is a little |
Artmoney is a little convoluted for the beginner tbh - try cheat engine. Finding a float/real/single is fairly simple, they are indeed by definition 4 bytes Just be aware when searching for values that floats are not 100% accurate (by any stretch of the imagination), they are a binary "approximation/respresentation" of the number with a finite bit-length representation, additionally if for example x87 FPU operations have taken place on that number it could potentially result in a different rounding than expected due to a higher internal bit representation on the intermediate value. Thus you should never rely on 1.3333 actually equalling 1.3333, always drop a point or two of precision when searching for a value - you can search for something higher precision later, if the value is hard coded [aspect ratio normally always is] then you can search the hex representation fairly reliably, but sometimes (not always, occasionally) 1.3334 or 1.7778 or something to that affect may be used and your search would fail when searching for a rigid fixed value, eg. 1.777777 oo FOV can be somewhat more difficult, it could be radians or degrees, could be derived from a single base value or a set of seperate values, normally you would start with trying to find a way to influence change on the FOV then look for a value that is changing appropriately, after finding the value you can go about investigating what code accesses that value and modifying it appropriately. |
|
| Author: | Rope [ 13 May 2012, 17:59 ] |
| Post subject: | Hi guys, thanks for the |
Hi guys, thanks for the answers and sorry for my late reply. So as I understand, I need to look for the hexadecimal value of the aspect ratio, without knowing to what decimal number it has been rounded. Is that correct? So it could be anything like 1.33, 1.333, 1.3333, 1.34, 1.334, 1.3334, and so on, right? It's too bad nobody wrote some sort of simple tutorial to find the FOV in ArtMoney like they did for the width and height for the resolution, there's a lot of old and not so old games that just need a FOV fix to be properly widescreen. |
|
| Author: | dopefish [ 14 May 2012, 01:16 ] |
| Post subject: | Finding the field-of-view is |
Finding the field-of-view is pretty easy usually. Just do a memory scan for an unknown float value—or use a specific range if you know what it might be—and then zoom in and out and re-search for values that changed each time. Eventually you'll narrow it down. From here you'll want to do a pointer scan or find out which part of the game's code writes and modifies it. |
|
| Author: | Rope [ 14 May 2012, 02:07 ] |
| Post subject: | To be honest, I realise that |
To be honest, I realise that I don't have the knowledge to do this, not yet at least. I tried with ArtMoney, but there's just too many things I don't understand about it. If it is so simple, would you perhaps have the chance to filter out the FOV data for ObsCure II? Or even better it would be to make a mini tutorial on how to find the FOV data in ArtMoney, like there is one for the resolution. I'm sure a lot of people would be greatful. |
|
| Page 1 of 1 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|